Wall GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A SHADE
3
2 LAMP
SOCKET WASHER
1
THUMB SCREW
1 1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
3
Install the shade by placing it over the socket, then using the washers and thumb screws to secure it.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A OMBRE
3
AMPOULE
2
DOUILLE RONDELLE
1
VIS DE SERRAGE
1 1
Suivez les instructions d'installation jointes supplément pour l'installation électrique et de fixation sur la boîte de sortie de la maison.
2
Vissez la lampe dans la douille. Reportez-vous à l'étiquette sur la douille de lampe Puissance max pour plus d'informations.
3
Installez l'ombre en le plaçant sur le socket, puis en utilisant les rondelles et les vis à oreilles pour le fixer.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A SOMBRA
3
BOMBILLA
2
ENCHUFE ARANDELA
1
TORNILLO DE MARIPOSA
1 1
Siga las instrucciones de instalación adjuntas suplemento para la instalación eléctrica y el accesorio en la caja de salida casa.
2
Atornille la lámpara en el zócalo. Consulte la etiqueta del casquillo de la lámpara para obtener información Potencia Max.
3
Instale la sombra colocándolo sobre el zócalo, a continuación, utilizando las arandelas y los tornillos de mariposa para fijarlo.
Secure the mounting plate to the electrical box with the two provided mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire w
Suivez les instructions d'installation jointes supplément pour l'installation électrique et de fixation sur la boîte de sortie de la maison. Vissez la lampe dans la ...
junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Mark the anchor hole locations on the mounting plate and remove the mounting plate. ... Connect the black fixture wire to the hot power line wire with a wire nut.
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Hounslow 1 Light Pendant. 1.1. P1309-P1310-P1319-P1320. Pendant. P1309, P1310,. P1319, P1320. Place the shade and spacer over the socket, then secure ...
qu'il entraîne. Utiliser les conducteurs d'alimentation supérieure à 90° c. VIS DE POSTE. POSTE. 1. 2. 3. 4. 5. 6. 7. AMPOULE. PANNEAU DE VERRE. 5. 6. 7 ...
Refer to the label on the lamp socket for Max Wattage information. Repeat steps 1-3 for remaining sockets. Using the help of another person, connect the upper ...
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
This product is safety listed for dry locations only. This product may be dimmed ... with the construction and operation of the product and the hazards involved.
W 1782. B. Wall. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant. NEC junction boxes. This product is ...
WB1713. WB1713. Install the glass panels by sliding them into the fixture and securing them using the tabs. Secure the mounting plate to the electrical box with ...
Mount the fixture base onto the mounting plate and secure it with the Allen screws using an Allen wrench. Screw the lamp into the socket. Refer to the label on ...
Install the mounting plate to the junction box with junction box screws (not provided) ... screws to mount the fixture later. ... Use minimum 90°c supply conductors.
compliant. NEC junction boxes. This product is safety listed for damp locations. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the.
luminaire et le fixer avec la petite vis de fixation à l'aide d'une clé Allen. Fixez le bras à la ... 555 Theodore Fremd Ave Suite B101 Rye, NY 10580. 800.969.3347.
Refer to the label on the lamp socket for Max Wattage information. Place and secure shade onto ... 7400 Linder Ave, Skokie, IL 60077. 800.969.3347 www.Feiss.
This instruction shows a typical installation. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Install the candle follower by placing it on top of the candle tube. Screw the lamp into the ... and the hazards involved. Use minimum
P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing ... Refer to the label on the lamp socket for Max Wattage information.
