Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws. Install the candle tube by slipping through socket. Place the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information. Install the shade by ...
Wall GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations.
1A SHADE
8
ELECTRICAL BOX
NEUTRAL WIRE LAMP
7 1
CANDLE TUBE
6
WHITE WIRE
MOUNTING PLATE
1 SOCKET
MOUNTING PLATE SCREW
10 10
HOT WIRE
DECORATIVE STRAND
5
FIXTURE SCREW
BLACK WIRE
ALLEN WRENCH 1
Secure the mounting plate to the electrical box with the two mounting plate screws.
2
Connect the fixture ground wire to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5
Mount the fixture base onto the mounting plate and secure it with the fixture screws.
6
Install the candle tube by slipping through socket.
7
Place the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
8
Install the shade by properly placing it over the lamp.
9
If necessary, repeat steps 6-8 for remaining shades.
10
Install the decorative strands by hooking them to the fixture. 1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A ABAT-JOUR
8
FIL NEUTRE
BOÎTE ÉLECTRIQUE
7
AMPOULE
1 TUBE BOUGIE
6
FIL BLANC PLAQUE DE MONTAGE
1 DOUILLE
VIS DE MONTAGE
10 10
FIL CHAUD
CHAPELET DÉCORATIF
5
VIS DE LUMINAIRE
FIL NOIR
CLÉ ALLEN
1
Fixez la plaque de montage à la boîte électrique avec les deux vis de montage.
2
Connectez le fil de terre du luminaire à un terrain approprié conformément aux codes électriques locaux.
3
Connectez le fil blanc du luminaire au fil de ligne à neutre avec un écrou de fil.
4
Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
5
Montez l'base du luminaire sur la plaque de montage et le fixer avec les vis de fixation.
6
Installer les tubes de bougie en les glissant à travers les douille.
7
Vissez le ampoule dans le douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
8
Installer l'abat-jour de placer correctement sur le ampoule.
9
Si nécessaire, répétez les étapes 6 à 8 pour le abat-jours restants.
10
Installer les chapelet décoratif en l'accrochant à le luminaire.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A PANTALLA
8
CABLE NEUTRO BOMBILLA
CAJA ELÉCTRICA
7 1
TUBO DE LA VELA
6
CABLE BLANCO
PLACE DE MONTAJE
1
ENCHUFE TORNILLO DE MONTAJE
10 10
CABLE CALIENTE
FILAMENTO DECORATIVO
5
TORNILLO DE LA LÁMPARA
CABLE NEGRO
LLAVE DE ALLEN
1
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje.
2
Conecte el cable de tierra a una tierra artefacto adecuado de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre.
4
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre.
5
Monte el base de la lámpara en la placa de montaje y fíjela con los tornillos de la lámpara .
6
Instale el tubo de la vela deslizándolos a través de el enchufe.
7
Atornille la bombilla en el enchufe. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
8
Instale la pantalla colocando correctamente sobre la bombilla.
9
Si es necesario, repita los pasos 6 a 8 para las pantallas restantes.
10
Instale las filamento decorativos enganchándolo en la lámpara
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the set screws. Install the shade by placing the shade, spacer, and collar nut over the socket, then using th
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws using an Allen wrench. Place the shade and spacer over the socket, then secure them in pla
Hamlet 1, 2, 3, and 4 Light Vanity Strip. 1.0. V 2250_. S. V 22501, V 22502,. S. S. V 22503, V 22504. S. S. Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. C
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre. Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre. Monte el base de la lámpara en la placa de
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws using ...
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut using the shade tool; repeat for remaining ... 5. 6. FIXTURE SCREW. 5. Wall. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ins
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SOCKET. M
Colby 1, 2, 3, and 4 Light Vanity Strip. 1.1. VS4000_. Wall. VS4000_. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. This prod
5. 6. 7. COLLAR NUT. Secure the mounting plate to the junction box. ... Place the shade over the socket and secure it in place by screwing the collar nut onto the ...
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje. ... Conecte el cable blanco de la lámpara al cable de energía de la línea ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
... socket and secure it in place by screwing the collar nut onto the socket using the shade tool. Repeat for multiple shades. Screw the lamp(s) into the socket(s).
Vissez la tige unique à l'armature, puis placer l'ensemble de la tige sur la tige unique et ... Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply ...
V 2040_. S. Vanity Strip. 1. 6. 7. COLLAR NUT. SPACER. Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ...
Connect the white fixture wire to the neutral power line wire with a wire nut. ... Place the shade onto the socket and secure it in place by screwing the collar nut ...
com.ar. Hasta el 31/12/2012. Gastronomía. ◗ .... Jordania, recibe órdenes vía satélite de Ed Hoffman, un agente de inteligencia. Cerca de su objetivo, Ferris ...
