IMPORTANT NOTE: - Place all laminated parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched. - Check to make sure that you have all parts and hardware. - Remove all wrapping materials, including staples and packaging straps before your start to assemble. - Do not tighten ...
Check to make sure that you have all parts and hardware. - Remove all wrapping materials, ... Keep all hardware parts out of children's reach. - It is recommended for 2 ... Coloque todas las partes laminadas sobre una superficie limpia y uniforme (co
Follow the arrow mark on the battery cover to remove the cover. 3. Insert two AA size batteries into the compartment as indicated by the polarity markings. 4. Replace the battery compartment cover. SETTING THE TIME. Q Once the batteries are installed
Page 1. ®. Page 2. 40mm. X4. X4. B. H. 10mm. I. 4mm. X1. X4. G. 15mm. A. B. C. C. D. E. E. F. F. G. I. G. B. B. H. I. I. Page 3. 40mm. X4. X4. B. H. 10mm. I. 4mm. X1. X4. G. 15mm. A. B. C. C. D. E. E. F. F. G. I. G. B. B. H. I. I. Page 4. 40mm. X4. X
Cadre équipé d'une barre de mousse pour permettre d'y planter des punaises. Supports muraux 1pc. 1pc. 1pc. 1pc. FIXATION DE L'AUGET POUR STYLOs sur le CADRE DU TABLEAU. Arrière de conseil. Plumier. 1. Positionnez l'auget pour stylos à l'endroit souha
PARA MEJORAR LA RECEPCIDN DE LA SENAL DE RADIO: Q No coloque el reloj demasiado cerca de equipos eléctricos, tales como televisores, computadoras, bocinas, videocaseteras o méquinas de fax. Q No lo coloque encima de superficies metélicas o cerca de e
peuvent pas livrer a ces boîtes. 3. Numéro de téléphone. 4. Numéro de modèle. 5. Numéro de pièce. 6. Numéro de facture. 7. Date d'achat. Remarque: Notre politique est d'envoyer toutes les pièces demandées par transport terrestre normal. Sivous voulez
Assemble posts by taking one short post with threaded stud and inserting into wide threaded hole of another ... Stand one shelf on its side and insert the posts with the plastic shelf supports in place up through the shelf ... l'extrémité évasée et p
The Stack and Shred 130X/130M has been designed to automatically shred up to 130 sheets from the auto-feed chamber and up to 6 sheets through the manual feed slot. The auto-feed mechanism has been designed to handle paper fastened with staples and pa
4 clock-wise to tight them. Use the phillips screwdriver to rotate the camlocks. Connect the assembled parts to the side panels. hole top panel bottom panel.
Do not tighten all screws/bolts until pieces are completely assembled. • Keep all ... S'assurer d'être en possession de toutes les pièces et de toute la quincaillerie.
The pneumatic cylinder for the seat height adjustment is adjusting to your body weight. ... Pull lever D backward to allow seat to tilt forward - or - push lever D ...
Gardez toutes les pièces de quincaillerie hors de portée des enfants. • Il est recommandé que 2 personnes effectuent cet assemblage. II. 2 personnes sont ...
3447 3448. 3452 3453. Cava® Collection Guest Chairs. A S S E M B L Y I N S T R U C T I O N S. I N S T R U C T I O N S. New Hope, MN 55428. Visit us on the ...
Install the 10W LED Bulb (D) into the socket of the lamp holder and screw it tightly in. 6. ... Plug into wall outlet. 8. Turn the lamp on .... Numéro de téléphone. 4.
Mesh Task Arm Chair. Fauteuil de travail en toile. Şilla de Trabajo con Descansabrazos y Malla. LLR69518. Please unscrew all hardware from cushion before ...
If you are missing parts or have other concerns, please email [email protected] or fax: 404-472-9063. ... pièces ou que vous éprouvez d'autres inquiétudes.
Auto position. The unit is now ready for use. The power cord should be plugged directly into the outlet and not used in conjunction with a power extension cord, ...
Adjust the brightness of the lamp by tapping the “touch” switch. 7. To turn off lamp, tap the “touch” switch. USB Docking Station & Charging Port: Output: 5Vdc Max 750mA. Use to dock and charge small personal “smart” devices such as cell phones, MP3
Place all laminated part on a clean and smooth surface such as a rug or carpet to avoid the parts from ... Remove all wrapping materials including staples & packaging straps before you start to assemble ... Coloque todas las partes laminadas sobre un
Do not tighten all screws/bolts until pieces are completely assembled. • Keep all ... Lay out the parts on a non-abrasive surface such as carpet or blanket.
